Time series data stream (TSDS)

A time series data stream (TSDS) models timestamped metrics data as one or more time series.

You can use a TSDS to store metrics data more efficiently. In our benchmarks, metrics data stored in a TSDS used 70% less disk space than a regular data stream. The exact impact will vary per data set.

Both a regular data stream and a TSDS can store timestamped metrics data. Only use a TSDS if you typically add metrics data to Elasticsearch in near real-time and @timestamp order.

A TSDS is only intended for metrics data. For other timestamped data, such as logs or traces, use a logs data stream or regular data stream.

A TSDS works like a regular data stream with some key differences:

A time series is a sequence of observations for a specific entity. Together, these observations let you track changes to the entity over time. For example, a time series can track:

Figure 3. Time series of weather sensor readings plotted as a graph

In a TSDS, each Elasticsearch document represents an observation, or data point, in a specific time series. Although a TSDS can contain multiple time series, a document can only belong to one time series. A time series can’t span multiple data streams.

Dimensions are field names and values that, in combination, identify a document’s time series. In most cases, a dimension describes some aspect of the entity you’re measuring. For example, documents related to the same weather sensor may always have the same sensor_id and location values.

A TSDS document is uniquely identified by its time series and timestamp, both of which are used to generate the document _id. So, two documents with the same dimensions and the same timestamp are considered to be duplicates. When you use the _bulk endpoint to add documents to a TSDS, a second document with the same timestamp and dimensions overwrites the first. When you use the PUT /<target>/_create/<_id> format to add an individual document and a document with the same _id already exists, an error is generated.

You mark a field as a dimension using the boolean time_series_dimension mapping parameter. The following field types support the time_series_dimension parameter:

For a flattened field, use the time_series_dimensions parameter to configure an array of fields as dimensions. For details refer to flattened.

Dimension definitions can be simplified through pass-through fields.

Metrics are fields that contain numeric measurements, as well as aggregations and/or downsampling values based off of those measurements. While not required, documents in a TSDS typically contain one or more metric fields.

Metrics differ from dimensions in that while dimensions generally remain constant, metrics are expected to change over time, even if rarely or slowly.

To mark a field as a metric, you must specify a metric type using the time_series_metric mapping parameter. The following field types support the time_series_metric parameter:

Accepted metric types vary based on the field type:

The matching index template for a TSDS must contain a data_stream object with the index_mode: time_series option. This option ensures the TSDS creates backing indices with an index.mode setting of time_series. This setting enables most TSDS-related functionality in the backing indices.

If you convert an existing data stream to a TSDS, only backing indices created after the conversion have an index.mode of time_series. You can’t change the index.mode of an existing backing index.

When you add a document to a TSDS, Elasticsearch automatically generates a _tsid metadata field for the document. The _tsid is an object containing the document’s dimensions. Documents in the same TSDS with the same _tsid are part of the same time series.

The _tsid field is not queryable or updatable. You also can’t retrieve a document’s _tsid using a get document request. However, you can use the _tsid field in aggregations and retrieve the _tsid value in searches using the fields parameter.

In a TSDS, each backing index, including the most recent backing index, has a range of accepted @timestamp values. This range is defined by the index.time_series.start_time and index.time_series.end_time index settings.

When you add a document to a TSDS, Elasticsearch adds the document to the appropriate backing index based on its @timestamp value. As a result, a TSDS can add documents to any TSDS backing index that can receive writes. This applies even if the index isn’t the most recent backing index.

If no backing index can accept a document’s @timestamp value, Elasticsearch rejects the document.

Elasticsearch automatically configures index.time_series.start_time and index.time_series.end_time settings as part of the index creation and rollover process.

Use the index.look_ahead_time index setting to configure how far into the future you can add documents to an index. When you create a new write index for a TSDS, Elasticsearch calculates the index’s index.time_series.end_time value as:

now + index.look_ahead_time

At the time series poll interval (controlled via time_series.poll_interval setting), Elasticsearch checks if the write index has met the rollover criteria in its index lifecycle policy. If not, Elasticsearch refreshes the now value and updates the write index’s index.time_series.end_time to:

now + index.look_ahead_time + time_series.poll_interval

This process continues until the write index rolls over. When the index rolls over, Elasticsearch sets a final index.time_series.end_time value for the index. This value borders the index.time_series.start_time for the new write index. This ensures the @timestamp ranges for neighboring backing indices always border but never overlap.

Use the index.look_back_time index setting to configure how far in the past you can add documents to an index. When you create a data stream for a TSDS, Elasticsearch calculates the index’s index.time_series.start_time value as:

now - index.look_back_time

This setting is only used when a data stream gets created and controls the index.time_series.start_time index setting of the first backing index. Configuring this index setting can be useful to accept documents with @timestamp field values that are older than 2 hours (the index.look_back_time default).

A TSDS is designed to ingest current metrics data. When the TSDS is first created the initial backing index has:

Only data that falls inside that range can be indexed.

You can use the get data stream API to check the accepted time range for writing to any TSDS.

Within each TSDS backing index, Elasticsearch uses the index.routing_path index setting to route documents with the same dimensions to the same shards.

When you create the matching index template for a TSDS, you must specify one or more dimensions in the index.routing_path setting. Each document in a TSDS must contain one or more dimensions that match the index.routing_path setting.

The index.routing_path setting accepts wildcard patterns (for example dim.*) and can dynamically match new fields. However, Elasticsearch will reject any mapping updates that add scripted, runtime, or non-dimension fields that match the index.routing_path value.

Pass-through fields may be configured as dimension containers. In this case, their sub-fields get included to the routing path automatically.

TSDS documents don’t support a custom _routing value. Similarly, you can’t require a _routing value in mappings for a TSDS.

Elasticsearch uses compression algorithms to compress repeated values. This compression works best when repeated values are stored near each other — in the same index, on the same shard, and side-by-side in the same shard segment.

Most time series data contains repeated values. Dimensions are repeated across documents in the same time series. The metric values of a time series may also change slowly over time.

Internally, each TSDS backing index uses index sorting to order its shard segments by _tsid and @timestamp. This makes it more likely that these repeated values are stored near each other for better compression. A TSDS doesn’t support any index.sort.* index settings.

Now that you know the basics, you’re ready to create a TSDS or convert an existing data stream to a TSDS.