Discovery
editDiscovery
editDiscovery is the process by which the cluster formation module finds other nodes with which to form a cluster. This process runs when you start an Elasticsearch node or when a node believes the master node failed and continues until the master node is found or a new master node is elected.
This process starts with a list of seed addresses from one or more seed hosts providers, together with the addresses of any master-eligible nodes that were in the last-known cluster. The process operates in two phases: First, each node probes the seed addresses by connecting to each address and attempting to identify the node to which it is connected and to verify that it is master-eligible. Secondly, if successful, it shares with the remote node a list of all of its known master-eligible peers and the remote node responds with its peers in turn. The node then probes all the new nodes that it just discovered, requests their peers, and so on.
If the node is not master-eligible then it continues this discovery process
until it has discovered an elected master node. If no elected master is
discovered then the node will retry after discovery.find_peers_interval
which
defaults to 1s
.
If the node is master-eligible then it continues this discovery process until
it has either discovered an elected master node or else it has discovered
enough masterless master-eligible nodes to complete an election. If neither of
these occur quickly enough then the node will retry after
discovery.find_peers_interval
which defaults to 1s
.
Once a master is elected, it will normally remain as the elected master until it is deliberately stopped. It may also stop acting as the master if fault detection determines the cluster to be faulty. When a node stops being the elected master, it begins the discovery process again.
Refer to Troubleshooting discovery for troubleshooting issues with discovery.
Seed hosts providers
editBy default the cluster formation module offers two seed hosts providers to
configure the list of seed nodes: a settings-based and a file-based seed
hosts provider. It can be extended to support cloud environments and other
forms of seed hosts providers via discovery plugins.
Seed hosts providers are configured using the discovery.seed_providers
setting, which defaults to the settings-based hosts provider. This setting
accepts a list of different providers, allowing you to make use of multiple
ways to find the seed hosts for your cluster.
Each seed hosts provider yields the IP addresses or hostnames of the seed
nodes. If it returns any hostnames then these are resolved to IP addresses
using a DNS lookup. If a hostname resolves to multiple IP addresses then Elasticsearch
tries to find a seed node at all of these addresses. If the hosts provider does
not explicitly give the TCP port of the node by then, it will implicitly use the
first port in the port range given by transport.profiles.default.port
, or by
transport.port
if transport.profiles.default.port
is not set. The number of
concurrent lookups is controlled by
discovery.seed_resolver.max_concurrent_resolvers
which defaults to 10
, and
the timeout for each lookup is controlled by discovery.seed_resolver.timeout
which defaults to 5s
. Note that DNS lookups are subject to
JVM DNS caching.
Settings-based seed hosts provider
editThe settings-based seed hosts provider uses a node setting to configure a static list of the addresses of the seed nodes. These addresses can be given as hostnames or IP addresses; hosts specified as hostnames are resolved to IP addresses during each round of discovery.
The list of hosts is set using the discovery.seed_hosts
static setting. For example:
The port will default to |
|
If a hostname resolves to multiple IP addresses, Elasticsearch will attempt to connect to every resolved address. |
File-based seed hosts provider
editThe file-based seed hosts provider configures a list of hosts via an external file. Elasticsearch reloads this file when it changes, so that the list of seed nodes can change dynamically without needing to restart each node. For example, this gives a convenient mechanism for an Elasticsearch instance that is run in a Docker container to be dynamically supplied with a list of IP addresses to connect to when those IP addresses may not be known at node startup.
To enable file-based discovery, configure the file
hosts provider as follows
in the elasticsearch.yml
file:
discovery.seed_providers: file
Then create a file at $ES_PATH_CONF/unicast_hosts.txt
in the format described
below. Any time a change is made to the unicast_hosts.txt
file the new
changes will be picked up by Elasticsearch and the new hosts list will be used.
Note that the file-based discovery plugin augments the unicast hosts list in
elasticsearch.yml
: if there are valid seed addresses in
discovery.seed_hosts
then Elasticsearch uses those addresses in addition to those
supplied in unicast_hosts.txt
.
The unicast_hosts.txt
file contains one node entry per line. Each node entry
consists of the host (host name or IP address) and an optional transport port
number. If the port number is specified, is must come immediately after the
host (on the same line) separated by a :
. If the port number is not
specified, Elasticsearch will implicitly use the first port in the port range given by
transport.profiles.default.port
, or by transport.port
if
transport.profiles.default.port
is not set.
For example, this is an example of unicast_hosts.txt
for a cluster with four
nodes that participate in discovery, some of which are not running on the
default port:
10.10.10.5 10.10.10.6:9305 10.10.10.5:10005 # an IPv6 address [2001:0db8:85a3:0000:0000:8a2e:0370:7334]:9301
Host names are allowed instead of IP addresses and are resolved by DNS as described above. IPv6 addresses must be given in brackets with the port, if needed, coming after the brackets.
You can also add comments to this file. All comments must appear on their lines
starting with #
(i.e. comments cannot start in the middle of a line).
EC2 hosts provider
editThe EC2 discovery plugin adds a hosts provider that uses the AWS API to find a list of seed nodes.
Azure Classic hosts provider
editThe Azure Classic discovery plugin adds a hosts provider that uses the Azure Classic API find a list of seed nodes.
Google Compute Engine hosts provider
editThe GCE discovery plugin adds a hosts provider that uses the GCE API find a list of seed nodes.